Elta LE100 Spezifikationen Seite 205
- Seite / 254
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 7 –Communication Performance Verification
198 PL 3120/PL 3150/PL 3170 Power Line Smart Transceiver Data Boo
k
Good Citizen Verification
The following steps are used to verify that the Unit Under Test (UUT) does not inject unwanted noise onto the power
mains or excessively load the power mains.
Unintentional Output Noise Verification
The following procedure determines if the UUT is generating unwanted noise which might hinder its communication
performance or that of other devices on the power mains.
1. Connect a single PLCA-22 analyzer, the UUT, and the Isolator as shown in Figure 7.6 below. Verify that the ana-
lyzer is set for the same band of operation as the UUT (A-band or C-band) by observing the selected band in the
upper right-hand corner of the LCD display (if its band setting does not match, then it must be changed using the
Setup screen of the analyzer). Leave the PLCA-22 analyzer in idle mode (no packets being transmitted) and set it for
Internal and Line-to-Neutral coupling (coupling mode switch to the right).
2. Verify that the UUT application program is not sending messages.
3. Observe the signal strength bar graph LEDs. The -72dB LED should not be on solid and the -66dB LED should not
be flashing on either the primary or secondary bar graph meters. In addition, the Packet Detect (PKD) LEDs should
not flash any more than once per minute.
4. Record the results from Step 3 in Table 7.1 at the end of this chapter.
.
Figure 7.6 Unintentional Output Noise Verification
Unit Under Test
(UUT)
service pin
PLCA-22
To power
mains
packet detect LED
ISOLATOR
Recv
Isloated Power Line
- /PL 3150 1
- /PL 3170 1
- Table of Contents 3
- Product Overview 9
- LONWORKS Networks 9
- Three Product Families 10
- Power Line Signaling 10
- Restricted 11
- Forward Error Correction 12
- Powerful Output Amplifier 12
- Wide Dynamic Range 12
- Low Current Consumption 12
- Restrictions Under 13
- Consideration 13
- Overview 17
- Table 2.5 ALU Instructions 22
- Memory Allocation Overview 23
- • Unique 48-bit Neuron ID 24
- Static RAM 26
- Pre-programmed ROM 26
- Input/Output 27
- Clock Input 28
- PL Smart 29
- Transceiver 29
- Connections 30
- TXON Output Signal 30
- Additional Functions 31
- RESET~ Pin 32
- Reset Processes and Timing 34
- SERVICE~ Pin 39
- Signal Out 40
- Integrity Mechanisms 41
- Reset Processing 43
- Signatures 43
- Hardware Considerations 46
- Pulsecount Input 50
- I/O Timing Issues 51
- Direct I/O Objects 53
- Byte Input/Output 55
- Leveldetect Input 56
- Nibble Input/Output 57
- Parallel I/O Objects 58
- Parallel Input/Output 60
- Serial I/O Objects 66
- C Input/Output 68
- Magcard Input 70
- Magtrack1 Input 72
- Magcard Bitstream Input 73
- Serial Input/Output 77
- Touch Input/Output 79
- Wiegand Input 81
- SCI (UART) Input/Output 82
- SPI Input/Output 83
- IO_7 input bit io_p7_in; 84
- 1 = clockedge(+) 85
- 0 = clockedge(-) 85
- 1 = [default] 85
- 0 = invert 85
- SPI Master 87
- SPI Master (Neurowire 87
- SPI Slave 88
- Timer/Counter Input Objects 89
- Dualslope Input 90
- Edgelog Input 91
- Infrared Input 93
- Ontime Input 94
- Period Input 94
- Reference Figure 3.40 95
- Quadrature Input 97
- Return from function 88 µs 98
- Totalcount Input 99
- Timer/Counter Output Objects 100
- Frequency Output 102
- Infrared Pattern Output 103
- Oneshot Output 104
- Pulsecount Output 105
- Pulsewidth Output 106
- Triac Output 107
- Triggered Count Output 109
- (Clock Select + n) 110
- Clock Select 111
- Introduction 113
- IllinoisCap/154MKP275KB 116
- IllinoisCap/683MKP275KB 120
- IllinoisCap/224MKP275KB 128
- Table 4.12 136
- Coupling Circuit Tutorial 137
- Power Line Coupling Basics 139
- Power Line Coupling Details 141
- Safety Issues 146
- Ground Leakage Currents 148
- 3-Phase Coupling Circuits 149
- Line Surge Protection 155
- Transmission 164
- Retransmit 164
- Power Supply 166
- PL 3120/ PL 3170 167
- Reference Design 167
- (See Appendix A) 167
- 12.6 VAC @100 mA 168
- (See Text) 172
- Optional 172
- Quasi-peak detector 181
- Average detector 181
- Frequency (Hz) 186
- Attenuation (dB) 186
- Conducted Emissions Testing 194
- EMI Remedies 195
- Verification Procedure 201
- Power Line Test Isolator 202
- Test Equipment 202
- 30.1k Ω ±1%, 1/4W 204
- Good Citizen Verification 205
- ISOLATOR 207
- Checks 213
- Dual Carrier Frequency Mode 215
- CENELEC Access Protocol 215
- Power Management 216
- Standard Transceiver Types 217
- Development Tools Support 218
- ShortStack Developer’s Kit 220
- Reference Design Files 225
- (DSK) Reference Designs 227
- Device Checklist 232
- Ω @100kHz 234
- Schematic 239
- Production Test Guidelines 243
- A/D, D/A- based Test System 245
- Test System Verification 247
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern